直しました naoshimashita—fixed

Since arriving back in Ireland, we’ve mostly been getting by without a car, while awaiting the arrival of our car from Japan. However, for the past couple of weeks we’ve benefited from the generosity of my stepmother, who has been kind enough to lend us her car while on holiday in Canada.

The car had one minor problem which she asked me to look at if I had the chance: the mileometer/odometer display was faulty.

DSC_0094

It’s an LCD 7-segment display of the kind used in calculators, and I’ve seen calculators with the same fault. The calculation works fine, but the display is faulty.

I figured that if I could get at the connectors at the edge of the display, I could inspect them and clean them and see if there was any obvious problem, such as a short circuit due to dirt or condensation, or dry (cracked) solder joints.

First I had to remove the instrument panel from the car. This turned out to be quite easy and straightforward.

The instrument panel plastic surround is held in place by three screws (Phillips #2) along the underside of the upper shade.

DSC_0095 DSC_0097 DSC_0096

This plastic surround is connected to the plastic upper cover of the steering column, which is held in place by a clip on each side and is easily removed using a flat-bladed screwdriver.

DSC_0098

The plastic surround contains the electric boot release switch, so this had to be disconnected before it could be pulled free.

DSC_0100

DSC_0101

Now that’s out of the way, the instrument panel itself is held in place by another four Phillips screws – 2 at the bottom and 1 each at the right and left.

DSC_0103 DSC_0104 DSC_0102

Once these screws are removed, the whole panel can be pulled out and forward, allowing access to the wiring connection at the back. It’s probably a good idea to turn off the ignition before disconnecting the instruments.

The plug is secured in place by an ingenious clamping arrangement, released by sliding the black plastic clamp to the left.

DSC_0107

DSC_0108

Now the whole instrument panel can be lifted out. Good idea to put it face down on a newspaper or cloth to protect the lens from getting scratched.

DSC_0109

The back cover was held in place by 2 screws (Torx 10) and 4 clips around the outside. Removing the back cover exposed the printed circuit board (PCB). You can see a lot of brownish corrosion around some of the connectors, especially in the area directly behind the LCD display (top right of this picture).

DSC_0118

The front cover (including the lens) is only held in place by plastic clips and is easily removed, exposing the gauges.

DSC_0111

At this point, before removing the needles from the gauges, I took the precaution of taking a photo of the position of each one, so that I could return it to the same position. Another idea would be to mark the position with tape.

After removing the 4 needles (temp, tach, speed and fuel), and 5 more Torx screws holding the front panel in place, I was able to lift off the front panel, with the intention of accessing the faulty LCD.

DSC_0116

With the front panel removed, it looked like this:

DSC_0117

Unfortunately, at this point I was not able to make any further progress in dismantling the LCD unit itself. My intention had been to inspect and clean the connectors.

However, I was able to clean the back of the PCB by spraying it with WD40 and rubbing with cotton buds. This was effective in removing a lot of the visible corrosion around the connectors.

I also used a hairdryer on the PCB for a few minutes – partly to dry it off and also with the idea that it might help to repair any dry solder joints. Although a hairdryer probably isn’t hot enough to reflow solder, I thought even softening the solder might help somewhat.

Finally, I reassembled the whole thing and mounted it back in the car. And to my very pleasant surprise, it works!

DSC_0120

Advertisements

2 thoughts on “直しました naoshimashita—fixed

  1. Glad you made it back. I’ll keep on reading your posts. I really loved your time in Japan and meeting your wife and twodogs. I am a sansei from Hawaii and I have never been to Japan. My grandparents, parents and my two sisters have visited, some day I’ll go. Thanks for keeping up your postings, I’m sure it is a lot of work.

    1. Thank you Stephanie! It has been wonderful to have such lovely readers following our adventure. I will try to find interesting material to write about. I hope you will have the chance to visit Japan soon and that you will really enjoy it when you get there. It will be interesting experience for you to travel in Japan as an American who looks Japanese!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s